Bercomac 700312-5 Manuel du propriétaire

1 BERCO Rotary Tiller Universal mount for YARD & GARDEN Tractors CAUTION: READ & FOLLOW ALL SAFETY RULES & INSTRUCTIONS BEFORE OPER

8 Tractors with angled transaxle: Install the mounting brackets (item 2), the angled end towards the front of the tractor and the hole (item 4) towar

9 ASSEMBLY *These measurements are given as a reference only. After installing the rotary tiller, the frame should be 4 1/2" to 5 1/2" off

10 Install the lift arm Install the lift arm (item 1) with four 5/16 x 3/4" bolts (item 2) and flange nuts. ASSEMBLY For Installation Purposes

11 Prepare the adjusting link as shown. Apply some grease on the adjusting rod (item 1). Insert the two nuts (item 2) on the adjusting rod and scre

12 ASSEMBLY STEP 3 ROTARY TILLER INSTALLATION: (Primary installation) Lower the lift arm to place the rotary tiller’s frame flat on the ground. Slid

13 ASSEMBLY Adjust tension Please refer to the Recommended Installation Chart that is included specific brands of tractors. Note: Choose the appropr

14 ASSEMBLY Install cable Install spring Install spring and stopper CLUTCH CABLE INSTALLATION Tractors with manual clutch mechanism: Disengage the c

15 ASSEMBLY Last adjustments Adjust tension Adjustment Requires adjustment Well adjusted Reinstall the rear wheels on the tractor. Move the lift a

16 ASSEMBLY On a level surface remove the mower deck from tractor. Remove the pin (item 1) from the working position and install it in the locked posi

17 ASSEMBLY Install the drive belt (item 1) on the engine pulley (item 2). Lift the support (item 3). If your tractor is equipped with a manual clut

2 LIMITED WARRANTY Bercomac Limitée 92, Fortin North, Adstock, Quebec, Canada, G0N 1S0Conditions and Products Covered: BERCOMAC guarantees any part

18 OPERATION BEFORE TILLING: -Mow the grass and weeds before tilling, these can wrap around the tines or tine shaft. -Remove all objects that can dama

19 OPERATION INSPECTING, CLEANING OR PARKING THE ROTARY TILLER TRANSPORTING THE ROTARY TILLER: Always lift the rotary tiller off the ground by lowerin

20 MAINTENANCE BELT REPLACEMENT: Primary belt: -Remove the belt from engine pulley. -Remove the bolt (item 1) that holds the idler (item 2). -Remove t

21 Note: To facilitate replacing the tines, you must remove the tiller from the tractor and turn it upside down. -Park the tractor safely. -Raise the

22 DISMOUNTING On a level surface, park the tractor and apply the parking brake. a) Install the pin (item 1) in the locked position. b) Lower the

23 TROUBLESHOOTING PROBLEM POSSIBLE CAUSES CORRECTIVE ACTION Tiller will not turn. Belt is damaged. Replace the belt. Belt is broken. Replace t

24 PARTS BREAKDOWN ROTARY TILLER (FRAME)

25 PARTS LIST ROTARY TILLER (FRAME) Ref. Réf. English description Description française Qty. Qté. Part # Pièce # 1 Frame Châssis 1 103436 2 Hitc

26 PARTS LIST ROTARY TILLER (FRAME) Ref. Réf. English description Description française Qty. Qté. Part # Pièce # 31 Pin-lock Goupille de barrure 1

27 Ref. Réf. English description Description française Qty. Qté. Part # Pièce # 61 Spacer Douille d'espacement 4 104583 62 Hex. socket set

1 TABLE OF CONTENTS INTRODUCTION ...

28 PARTS BREAKDOWN ROTARY TILLER (HEAD)

29 PARTS LIST ROTARY TILLER (HEAD) Ref. Réf. English description Description française Qty. Qté. Part # Pièce # 1 Frame Châssis 1 103417 2 Tine

30 PARTS LIST ROTARY TILLER (HEAD) Ref. Réf. English description Description française Qty. Qté. Part # Pièce # 28 Cotter pin 5/32" x 1"

31 TORQUE SPECIFICATION TABLE GENERAL TORQUE SPECIFICATION TABLEUSE THE FOLLOWING TORQUES WHEN SPECIAL TORQUES ARE NOT GIVEN NOTE: These values ap

32 ATTACHMENTS ROTARY BROOM #700380 with nylon brush. #700381 with polypropylene brush. Fits on same subframe as snowblower & utility blade. Req

33 NOTES ____________________________________________________________________________________________________________________________________________

34 WHEN PERFORMANCE & DEPENDABILITY ARE NON NEGOTIABLE ! Bercomac Limitée 92, Fortin North, Adstock, Quebec, Canada, G

2 INTRODUCTION TO THE PURCHASER This new accessory was carefully designed to give years of dependable service. This manual has been provided toassi

3 SAFETY PRECAUTIONS Careful operation is your best insurance against an accident. Read this section carefully before operating the vehicle and acces

4 OPERATION: 1. Do not put hands or feet near, under or inside rotating parts. 2. Exercise extreme caution when operating on or crossing gravel

5 SAFETY DECALS REPLACE IF DECALS ARE DAMAGED SEE PARTS BREAKDOWN FOR DECAL LOCATION DECAL #105129 DECAL #105131 DECAL #105989 DECAL #105990 DECAL #10

6 ASSEMBLY IMPORTANT: TORQUE ALL BOLTS ACCORDING TO TORQUE SPECIFICATION TABLE WHEN STATED: TIGHTEN FIRMLY. REFER TO PARTS BREAKDOWN SECTION FOR PART

7 WARNING TO PREVENT INJURIES: Stop the motor. Apply parking brake. Remove the ignition key. Disconnect the wire from the spark plug(s) and keep aw